Parametertext ;Do not change these 3 lines Version = 12.04.06 ;Version of contents Syntax = 01 ;Version of Syntax ;--------------------------------------------------------------------------------------------------------------- ;PNR TEXTROT TEXTLIN [TOGROT] [TOGLIN] ;--------------------------------------------------------------------------------------------------------------- 1 "Actual traversing block - block number" "" {T0} 2 "Actual traversing block - position" "" {T0} 3 "Actual traversing block - velocity" "" {T0} 4 "Actual traversing block - acceleration override" "" {T0} 5 "Actual traversing block - deceleration override" "" {T0} 6 "Actual traversing block - command" "" {T0} 7 "Actual traversing block - command parameter" "" {T0} 8 "Actual traversing block - mode" "" {T0} 20 "Position setpoint" "" {T0} 21 "Position actual value" "" {T0} 22 "Distance to go" "" {T0} 23 "Velocity setpoint" "" {T0} 24 "Actual velocity" "" {T0} 25 "Effective override" "" {T0} 26 "Position actual value, external block change" "" {T0} 29 "Following error" "" {T0} 30 "Control deviation, position controller input" "" {T0} 31 "Actual Kv factor (position loop gain)" "" {T0} 32 "Position reference value, external" "" {T0} 79 "Reformat memory" "" {T0} 80 "Block number" "" {T0} 81 "Position" "" {T0} 82 "Velocity" "" {T0} 83 "Acceleration override" "" {T0} 84 "Deceleration override" "" {T0} 85 "Command" "" {T0} 86 "Command parameter" "" {T0} 87 "Mode" "" {T0} 91 "MDI position" "" {T0} 92 "MDI velocity" "" {T0} 93 "MDI acceleration override" "" {T0} 94 "MDI deceleration override" "" {T0} 97 "MDI mode" "" {T0} 100 "Dimension system" "" {T0} 101 "Actual dimension system" "" {T0} 102 "Maximum motor velocity" "" {T0} 103 "Maximum acceleration" "" {T0} 104 "Maximum deceleration" "" {T0} 105 "Override via SimoCom U" "" {T0} 106 "Time override active" "" {T0} 107 "Jerk limiting" "" {T0} 108 "Velocity setpoint jog 1" "" {T0} 109 "Velocity setpoint jog 2" "" {T0} 110 "Configuration, external block change" "" {T0} 111 "Normalization voltage, override" "" {T0} 112 "Normalization of override" "" {T0} 113 "Fixed endstop, configuration 1" "" {T0} 113b0 "Characteristics for the fixed endstop not reached" "" {T0} 113b1 "Characteristics for the clamping torque not reached" "" {T0} 114 "Fixed endstop, configuration 2" "" {T0} 115 "Fixed endstop, maximum following error" "" {T0} 116 "Fixed endstop, monitoring window" "" {T0} 118 "Software limit switch configuration" "" {T0} 118b0 "Behavior for software limit switch reached" "" {T0} 120 "Teach-in block" "" {T0} 121 "Teach-in standard block" "" {T0} 122 "Jogging 1 increments" "" {T0} 123 "Jogging 2 increments" "" {T0} 124 "Teach-in configuration" "" {T0} 124b0 "Automatic block change enable" "" {T0} 124b1 "Automatic block search" "" {T0} 125 "Spindle positioning active" "" {T0} 126 "Spindle positioning, zero mark tolerance window (BERO)" "" {T0} 127 "Spindle positioning, setting the internal zero mark" "" {T0} 128 "Spindle positioning offset, zero" "" {T0} 129 "Spindle positioning, tolerance search velocity" "" {T0} 130 "Spindle positioning, lowest search velocity" "" {T0} 131 "Spindle positioning, motion window" "" {T0} 132 "Spindle positioning, zero mark difference (BERO)" "" {T0} 133 "Spindle positioning, max. search velocity" "" {T0} 134 "Spindle positioning, positioning window reached" "" {T0} 136 "Spindle positioning active/inative" "" {T0} 137 "Spindle positioning status" "" {T0} 160 "Reference point coordinate" "" {T0} 162 "Reference point offset" "" {T0} 163 "Reference point approach velocity" "" {T0} 164 "Reference point creep speed" "" {T0} 165 "Reference point entry velocity" "" {T0} 166 "Reference cam approach direction" "" {T0} 167 "Invert, reference cams" "" {T0} 170 "Maximum distance to the reference cam" "" {T0} 171 "Max. distance between reference cam and zero pulse" "" {T0} 172 "Distance between reference cam and zero pulse" "" {T0} 173 "Reference point approach without reference cams" "" {T0} 174 "Referencing mode, position measuring system" "" {T0} 175 "Adjustment status - absolute position measuring system" "" {T0} 176 "Absolute encoder offset" "" {T0} 177 "Absolute encoder offset, low part" "" {T0} 178 "Absolute encoder offset, high part" "" {T0} 179 "mode, passive referencing" "" {T0} 200 "Kv factor (position loop gain)" "" {T0} 201 "backlash compensation" "" {T0} 203 "speed feedforward control mode" "" {T0} 204 "speed feedforward control factor" "" {T0} 205 "Balancing filter, speed feedforward control (deadtime)" "" {T0} 206 "Balancing filter, speed feedforward control (PT1)" "" {T0} 210 "Time constant, position setpoint filter" "" {T0} 231 "Position actual value inversion" "" {T0} 232 "Position setpoint inversion" "" {T0} 236 "Spindle pitch" "" {T0} 237 "Encoder revolutions" "" {T0} 238 "Load revolutions" "" {T0} 239 "Re-reference or re-adjust only if necessary" "" {T0} 241 "Activating, modulo conversion, rotary axis" "" {T0} 242 "Modulo range, rotary axis" "" {T0} 250 "Activate direct measuring system" "" {T0} 310 "Cam switching position 1" "" {T0} 311 "Cam switching position 2" "" {T0} 314 "Activating software limit switch" "" {T0} 315 "Minus software limit switch" "" {T0} 316 "Plus software limit switch" "" {T0} 318 "Dynamic following error monitoring tolerance" "" {T0} 320 "Position monitoring time" "" {T0} 321 "Positioning window" "" {T0} 325 "Standstill monitoring time" "" {T0} 326 "Standstill window" "" {T0} 400 "Reference point coordinates, master drive" "" {T0} 401 "Coupling factor, master drive revolutions" "" {T0} 402 "Coupling factor slave drive revolutions" "" {T0} 403 "Actual coupling factor, master drive revolutions" "" {T0} 404 "Actual coupling factor, slave drive revolutions" "" {T0} 410 "Configuration, coupling which can be switched-in" "" {T0} 412 "Synchronous offset position" "" {T0} 413 "Offset, synchronous velocity" "" {T0} 420 "Pos. difference, meas. probe to the zero point, slave drive" "" {T0} 425 "Coupling positions" "" {T0} 599 "Active motor data set" "" {T0} 600 "Operating display" "" {T0} 600b0 " " "" {T0} 600b1 " " "" {T0} 600b2 " " "" {T0} 600b3 " " "" {T0} 600b4 " " "" {T0} 600b5 " " "" {T0} 600b6 " " "" {T0} 600b7 " " "" {T0} 600b8 " " "" {T0} 600b9 " " "" {T0} 600b10 " " "" {T0} 600b11 " " "" {T0} 600b12 " " "" {T0} 600b13 " " "" {T0} 600b14 " " "" {T0} 600b15 " " "" {T0} 600b16 " " "" {T0} 600b17 " " "" {T0} 600b18 " " "" {T0} 600b19 " " "" {T0} 600b20 " " "" {T0} 600b21 " " "" {T0} 600b22 " " "" {T0} 600b23 " " "" {T0} 601 "Motor speed setpoint" "Velocity setpoint, motor" {T0} 602 "Actual motor speed" "Velocity actual value, motor" {T0} 603 "Motor temperature" "" {T0} 604 "Utilization, motor" "" {T0} 606 "Voltage at term. 56.x/14.x" "" {T0} 607 "Analog setpoint term. 56.x/14.x" "" {T0} 608 "Inversion term. 56.x/14.x" "" {T0} 609 "Smoothing time, terminal 56.x/14.x" "" {T0} 610 "Drift/offset correction term. 56.x/14.x" "" {T0} 611 "Voltage at term. 24.x/20.x" "" {T0} 612 "Analog setpoint term. 24.x/20.x" "" {T0} 613 "Inversion term. 24.x/20.x" "" {T0} 614 "Smoothing time, terminal 24.x/20.x" "" {T0} 615 "Drift/offset correction term. 24.x/20.x" "" {T0} 616 "Ramp-function generator ramp-up time" "" {T0} 617 "Ramp-function generator ramp-down time" "" {T0} 618 "Normalization voltage, speed setpoint" "" {T0} 619 "Normalization voltage, torque setpoint" "" {T0} 620 "Normalization voltage, torque/power reduction." "Normalization voltage, force/power reduction" {T0} 623 "DAC normalization, actual speed" "DAC normalization, motor actual velocity" {T0} 624 "DAC normalization, motor utilization" "" {T0} 625 "DAC normalization, torque setpoint" "DAC normalization, force setpoint" {T0} 626 "Signal number analog output term. 75.x/15" "" {T0} 627 "Shift factor analog output term. 75.x/15" "" {T0} 628 "Offset analog output term. 75.x/15" "" {T0} 629 "Segment address analog output term. 75.x/15" "" {T0} 630 "Offset address analog output term. 75.x/15" "" {T0} 631 "Bias protection, analog output, term. 75.x/15" "" {T0} 632 "Smoothing time, analog output, terminal 75.x/15" "" {T0} 633 "Signal number analog output term. 16.x/15" "" {T0} 634 "Shift factor analog output term. 16.x/15" "" {T0} 635 "Offset analog output term. 16.x/15" "" {T0} 636 "Segment address analog output term. 16.x/15" "" {T0} 637 "Offset address analog output term. 16.x/15" "" {T0} 638 "Bias protection, analog output, term. 16.x/15" "" {T0} 639 "Smoothing time, analog output, terminal 15.x/15" "" {T0} 641 "Fixed speed setpoint" "Fixed velocity setpoint" {T0} 649 "Delete parameters, drives A and B" "" {T0} 651 "Read and write protection" "" {T0} 652 "Transfer to FEPROM" "" {T0} 653 "Image, input signals, Part 1" "" {T0} 653b0 "ON / OFF1" "" {T0} 653b1 "Operating condition / OFF2" "" {T0} 653b2 "Operating condition / OFF3" "" {T0} 653b3 "Enable inverter/pulse inhibit" "" {T0} 653b4 "Ramp-fct.generator enable or OC/reject traversing task" "" {T0} 653b5 "Ramp-function generator start/stop or OC/intermed. stop" "" {T0} 653b6 "Enable setpoint and activate traversing task (edge)" "" {T0} 653b7 "Reset fault memory" "" {T0} 653b8 "Jog 1 ON / OFF" "" {T0} 653b9 "Jog 2 ON / OFF" "" {T0} 653b10 "Control requested / no control requested" "" {T0} 653b11 "Start referencing / exit referencing" "" {T0} 653b12 "Open holding braking as test/do no open" "" {T0} 653b13 "Ramp-up time zero w. control.enable or ext. block change" "" {T0} 653b14 "Open-loop torque controlled operation" "" {T0} 653b15 "Spindle positioning on or request passive referencing" "" {T0} 653b16 "Signal status, terminal 65.x" "" {T0} 653b17 "NE signal status, terminal 64" "" {T0} 653b18 "Signal status terminal 663 / terminal IF" "" {T0} 653b19 "NE signal status, terminal 63 / terminal 48" "" {T0} 653b21 "Equivalent zero mark" "" {T0} 653b22 "Flying measurement / length measurement" "" {T0} 654 "Image, input signals, Part 2" "" {T0} 654b0 "Parameter set switchover bit 0" "" {T0} 654b1 "Parameter set switchover bit 1" "" {T0} 654b2 "Parameter set switchover bit 2" "" {T0} 654b3 "First speed setpoint filter off" "" {T0} 654b4 "Ramp-up time zero" "" {T0} 654b5 "Siemens reserved (radial eccentricity monitoring)" "" {T0} 654b6 "Integrator disable speed controller" "" {T0} 654b7 "Select parking axis" "" {T0} 654b8 "Suppress fault 608" "" {T0} 654b9 "Motor changeover, bit 0" "" {T0} 654b10 "Motor changeover, bit 1" "" {T0} 654b11 "Motor changed over" "" {T0} 654b12 "Tracking operation" "" {T0} 654b13 "Set reference point" "" {T0} 654b14 "Reference cam" "" {T0} 654b15 "Fixed endstop, sensor" "" {T0} 654b16 "Plus hardware limit switch" "" {T0} 654b17 "Minus hardware limit switch" "" {T0} 654b18 "Fixed speed setpoint and block selection bit 0" "" {T0} 654b19 "Fixed speed setpoint and block selection bit 1" "" {T0} 654b20 "Fixed speed setpoint and block selection bit 2" "" {T0} 654b21 "Fixed speed setpoint and block selection bit 3" "" {T0} 654b22 "Block selection, bit 4" "" {T0} 654b23 "Block selection, bit 5" "" {T0} 655 "Image, input signal Part 3" "" {T0} 655b0 "Activate coupling" "" {T0} 655b1 "Jogging, incremental" "" {T0} 655b2 "Activate teach-in" "" {T0} 655b3 "Invert input pulses, angular encoder interface" "" {T0} 655b15 "Activate MDI" "" {T0} 655b21 "Activate the coupling via I0.x" "" {T0} 655b22 "Set position reference value" "" {T0} 656 "Image, output signals, Part 1" "" {T0} 656b0 "Ready to power-up / not ready to power-up" "" {T0} 656b1 "Ready to run or no fault" "" {T0} 656b2 "Status, controller enable" "" {T0} 656b3 "Fault available / no fault present" "" {T0} 656b4 "No OFF2 / OFF2 effective" "" {T0} 656b5 "No OFF3 / OFF3 effective" "" {T0} 656b6 "Power-on / No power-on inhibit" "" {T0} 656b7 "Alarm effective / No alarm present" "" {T0} 656b8 "n_set = n_act or no following error" "" {T0} 656b9 "Control requested" "" {T0} 656b10 "Comparison value reached or reference position reached" "" {T0} 656b11 "Reference point set / no reference point set" "" {T0} 656b12 "Setpoint acknowledgement (edge)" "" {T0} 656b13 "Fct. generator active or drive is stationary / drive moving" "" {T0} 656b14 "Open-loop torque controlled operation" "" {T0} 656b15 "Spindle positioning on or request passive referencing" "" {T0} 657 "Image, output signals, Part 2" "" {T0} 657b0 "Parameter set bit 0" "" {T0} 657b1 "Parameter set bit 1" "" {T0} 657b2 "Parameter set bit 2" "" {T0} 657b3 "First speed setpoint filter inactive" "" {T0} 657b4 "Ramp-function generator inactive" "" {T0} 657b5 "Open holding brake" "" {T0} 657b6 "Integrator disable speed controller" "" {T0} 657b7 "Parking axis selected" "" {T0} 657b8 "Suppress fault 608 active" "" {T0} 657b9 "Motor changeover, bit 0" "" {T0} 657b10 "Motor changeover, bit 1" "" {T0} 657b11 "Motor changeover running" "" {T0} 657b15 "MDI active" "" {T0} 657b18 "Status, block selection, bit 0" "" {T0} 657b19 "Status, block selection, bit 1" "" {T0} 657b20 "Status, block selection, bit 2" "" {T0} 657b21 "Status, block selection, bit 3" "" {T0} 657b22 "Status, block selection, bit 4" "" {T0} 657b23 "Status, block selection, bit 5" "" {T0} 658 "Image, output signals, Part 3" "" {T0} 658b0 "Ramp-up completed" "" {T0} 658b1 "|M| < M_x (P:1428, P:1429)" "" {T0} 658b2 "|n_act| < n_min (P:1418)" "" {T0} 658b3 "|n_act| < n_x (P:1417)" "" {T0} 658b4 "V_dc link > V_x (P:1604)" "" {T0} 658b5 "Variable signaling function" "" {T0} 658b6 "Motor temperature ok (motor temperature < P:1602)" "" {T0} 658b7 "Heatsink temperature ok" "" {T0} 658b8 "n_set = n_act (P:1426, P:1427)" "" {T0} 658b9 "Fixed endstop reached" "" {T0} 658b10 "Fixed endstop, clamping torque reached" "" {T0} 658b11 "Traverse to endstop active" "" {T0} 658b12 "Tracking active" "" {T0} 658b13 "Velocity limiting active" "" {T0} 658b14 "Setpoint available" "" {T0} 658b15 "Synchronized" "" {T0} 658b16 "Axis traverses forwards" "" {T0} 658b17 "Axis traverses backwards" "" {T0} 658b18 "Minus software limit switch approached" "" {T0} 658b19 "Plus software limit switch approached" "" {T0} 658b20 "Cam switching signal 1" "" {T0} 658b21 "Cam switching signal 2" "" {T0} 658b22 "Direct output 1 via traversing block" "" {T0} 658b23 "Direct output 2 via traversing block" "" {T0} 658b24 "Electronics temperature OK" "" {T0} 658b25 "i2t power section current not limited" "" {T0} 658b26 "Pulsed resistor not overloaded (only for POSMO CA)" "" {T0} 658b27 "Checkback signal, drive enable" "" {T0} 658b28 "Pulses enabled" "" {T0} 658b29 "Position reached" "" {T0} 658b30 "Spindle position 2 reached" "" {T0} 658b31 "Teach-in executed" "" {T0} 659 "Bootstrap loading" "" {T0} 660 "Function of input terminal I0.x" "" {T0} 661 "Function of input terminal I1.x" "" {T0} 662 "Function of input terminal I2.x" "" {T0} 663 "Function of input terminal I3.x" "" {T0} 664 "Function of input terminal I4" "" {T0} 665 "Function of input terminal I5" "" {T0} 666 "Function of input terminal I6" "" {T0} 667 "Function of input terminal I7" "" {T0} 668 "Function of input terminal I8" "" {T0} 669 "Function of input terminal I9" "" {T0} 670 "Function of input terminal I10" "" {T0} 671 "Function of input terminal I11" "" {T0} 672 "Function, input terminal I0.B" "" {T0} 676 "Assignment, inputs: Optional TERMINAL module" "" {T0} 677 "O1.x as input I2.x" "" {T0} 678 "Image of the input terminals" "" {T0} 678b0 "Signal state I0.x" "" {T0} 678b1 "Signal state I1.x" "" {T0} 678b2 "Signal state I2.x" "" {T0} 678b3 "Signal state I3.x" "" {T0} 678b4 "Signal status I4 (optional terminal module)" "" {T0} 678b5 "Signal status I5 (optional terminal module)" "" {T0} 678b6 "Signal status I6 (optional terminal module)" "" {T0} 678b7 "Signal status I7 (optional terminal module)" "" {T0} 678b8 "Signal status I8 (optional terminal module)" "" {T0} 678b9 "Signal status I9 (optional terminal module)" "" {T0} 678b10 "Signal status I10 (optional terminal module)" "" {T0} 678b11 "Signal status I11 (optional terminal module)" "" {T0} 678b12 "Signal status, terminal 65.x" "" {T0} 678b13 "NE signal status, terminal 64" "" {T0} 678b14 "Signal status terminal 663 / terminal IF" "" {T0} 678b15 "NE signal status, terminal 63 / terminal 48" "" {T0} 680 "signaling function of output terminal O0.x" "" {T0} 681 "signaling function of output terminal O1.x" "" {T0} 682 "signaling function of output terminal O2.x" "" {T0} 683 "signaling function of output terminal O3.x" "" {T0} 684 "signaling function, output terminal O4" "" {T0} 685 "signaling function, output terminal O5" "" {T0} 686 "signaling function, output terminal O6" "" {T0} 687 "signaling function, output terminal O7" "" {T0} 688 "signaling function, output terminal O8" "" {T0} 689 "signaling function, output terminal O9" "" {T0} 690 "signaling function, output terminal O10" "" {T0} 691 "signaling function, output terminal O11" "" {T0} 696 "Assignment, optional TERMINAL module outputs" "" {T0} 698 "Image of the output terminals" "" {T0} 698b0 "Signal state O0.x" "" {T0} 698b1 "Signal state O1.x" "" {T0} 698b2 "Signal state O2.x" "" {T0} 698b3 "Signal state O3.x" "" {T0} 698b4 "Signal status O4 (optional terminal module)" "" {T0} 698b5 "Signal status O5 (optional terminal module)" "" {T0} 698b6 "Signal status O6 (optional terminal module)" "" {T0} 698b7 "Signal status O7 (optional terminal module)" "" {T0} 698b8 "Signal status O8 (optional terminal module)" "" {T0} 698b9 "Signal status O9 (optional terminal module)" "" {T0} 698b10 "Signal status O10 (optional terminal module)" "" {T0} 698b11 "Signal status O11 (optional terminal module)" "" {T0} 699 "Inversion output terminal signals" "" {T0} 699b0 "Inverted: signal status O0.x" "" {T0} 699b1 "Inverted: signal status O1.x" "" {T0} 699b2 "Inverted: signal status O2.x" "" {T0} 699b3 "Inverted: signal status O3.x" "" {T0} 699b4 "Inverted: signal status O4 (optional terminal module)" "" {T0} 699b5 "Inverted: signal status O5 (optional terminal module)" "" {T0} 699b6 "Inverted: signal status O6 (optional terminal module)" "" {T0} 699b7 "Inverted: signal status O7 (optional terminal module)" "" {T0} 699b8 "Inverted: signal status O8 (optional terminal module)" "" {T0} 699b9 "Inverted: signal status O9 (optional terminal module)" "" {T0} 699b10 "Inverted: signal status O10 (optional terminal module)" "" {T0} 699b11 "Inverted: signal status O11 (optional terminal module)" "" {T0} 700 "Operating mode" "" {T0} 701 "Actual operating mode" "" {T0} 705 "Master Control" "" {T0} 706 "Sign-of-life Master Control" "" {T0} 709 "Control words via SimoCom U" "" {T0} 710 "Activate control words via SimoCom U" "" {T0} 711 "Input terminal signals via SimoCom U" "" {T0} 711b0 "SimoComU - input terminal signal I0.x" "" {T0} 711b1 "SimoComU - input terminal signal I1.x" "" {T0} 711b2 "SimoComU - input terminal signal I2.x" "" {T0} 711b3 "SimoComU - input terminal signal I3.x" "" {T0} 711b4 "SimoComU - input terminal signal I4" "" {T0} 711b5 "SimoComU - input terminal signal I5" "" {T0} 711b6 "SimoComU - input terminal signal I6" "" {T0} 711b7 "SimoComU - input terminal signal I7" "" {T0} 711b8 "SimoComU - input terminal signal I8" "" {T0} 711b9 "SimoComU - input terminal signal I9" "" {T0} 711b10 "SimoComU - input terminal signal I10" "" {T0} 711b11 "SimoComU - input terminal signal I11" "" {T0} 711b12 "SimoComU - controller enable at term. 65" "" {T0} 712 "Speed setpoint via SimoCom U" "Motor velocity setpoint via SimoCom U" {T0} 713 "Torque reduction via SimoCom U" "" {T0} 714 "Single block via SimoCom U: position" "" {T0} 715 "Single block via SimoCom U: velocity" "" {T0} 716 "Single block via SimoCom U: acceleration override" "" {T0} 717 "Single block via SimoCom U: deceleration override" "" {T0} 718 "Single block via SimoCom U: command" "" {T0} 719 "Single block via SimoCom U: command parameter" "" {T0} 720 "Single block via SimoCom U: mode" "" {T0} 730 "Saved parameters" "" {T0} 731 "Parameters required before start-up" "" {T0} 760 "Firmware download" "" {T0} 762 "Firmware download DP submodule" "" {T0} 801 "Changeover RS232/RS485" "" {T0} 802 "Drive number for RS485" "" {T0} 803 "Adjacent drive number" "" {T0} 820 "Fault end time" "" {T0} 821 "Time stamp, fault status change" "" {T0} 822 "Time stamp, warning status change" "" {T0} 823 "Fault number (active alarm)" "" {T0} 824 "Fault code (active alarm)" "" {T0} 825 "Fault time (active alarm)" "" {T0} 826 "Fault value (active alarm)" "" {T0} 827 "Acknowledge alarms" "" {T0} 828 "Warning value" "" {T0} 850 "Activate brake control" "" {T0} 851 "Brake release time" "" {T0} 852 "Speed, close holding brake" "Motor velocity, close holding brake" {T0} 853 "Brake delay time" "" {T0} 854 "Controller disable time" "" {T0} 868 "Baud rate selection, CAN bus" "" {T0} 870 "Module type" "" {T0} 871 "Module version" "" {T0} 872 "Option module type" "" {T0} 873 "Option module version" "" {T0} 874 "Drive position" "" {T0} 875 "Expected option module type" "" {T0} 879 "PROFIBUS configuration" "" {T0} 879b0 "Admissible sign-of-life error bit 0" "" {T0} 879b1 "Admissible sign-of-life error bit 1" "" {T0} 879b2 "Admissible sign-of-life error bit 2" "" {T0} 879b8 "Operation w/o sign-of-life monitor" "" {T0} 879b10 "Reserved" "" {T0} 879b11 "PKW processing: Subindex in the high byte" "" {T0} 879b12 "Activate direct measuring system" "" {T0} 879b13 "Incr. motor measuring sys.with/without equivalent zero mark" "" {T0} 879b14 "Incr. direct meas. system with/without equiv. zero mark" "" {T0} 879b15 "Reserved" "" {T0} 880 "Speed evaluation, PROFIBUS" "Motor velocity evaluation, PROFIBUS" {T0} 881 "Evaluation torque/power reduction PROFIBUS" "Evaluation force/power reduction PROFIBUS" {T0} 882 "Evaluation, torque setpont PROFIBUS" "Evaluation, force setpoint PROFIBUS" {T0} 883 "Override evaluation PROFIBUS" "" {T0} 884 "Position output evaluation PROFIBUS - number of increments" "" {T0} 888 "Function, distributed input (PROFIBUS)" "" {T0} 890 "Activate angular encoder/encoder interface" "" {T0} 891 "Source, external position reference value" "" {T0} 892 "No. of angular encoder marks / no. of encoder pulses factor" "" {T0} 893 "Angular encoder zero pulse offset" "" {T0} 894 "Angular encoder input signal waveform" "" {T0} 895 "External position reference value - number of increments" "" {T0} 896 "Ext. position ref. value - number of dimension system grids" "" {T0} 897 "Invert external position reference value" "" {T0} 898 "Modulo range master drive" "" {T0} 915 "PZD setpoint value assignment PROFIBUS" "" {T0} 916 "PZD actual value assignment PROFIBUS" "" {T0} 918 "PROFIBUS node address" "" {T0} 922 "PROFIBUS frame selection" "" {T0} 923 "List of PROFIBUS standard signals" "" {T0} 930 "PROFIBUS selector switch operating mode" "" {T0} 944 "Fault message counter" "" {T0} 945 "Fault code" "" {T0} 946 "Fault code list" "" {T0} 947 "Fault number" "" {T0} 948 "Fault time" "" {T0} 949 "Fault value" "" {T0} 951 "Fault number list" "" {T0} 952 "Number of faults" "" {T0} 953 "Warnings 800-815" "" {T0} 953b0 "800" "" {T0} 953b1 "801" "" {T0} 953b2 "802" "" {T0} 953b3 "803" "" {T0} 953b4 "804" "" {T0} 953b5 "805" "" {T0} 953b6 "806" "" {T0} 953b7 "807" "" {T0} 953b8 "808" "" {T0} 953b9 "809" "" {T0} 953b10 "810" "" {T0} 953b11 "811" "" {T0} 953b12 "812" "" {T0} 953b13 "813" "" {T0} 953b14 "814" "" {T0} 953b15 "815" "" {T0} 954 "Warnings 816-831" "" {T0} 954b0 "816" "" {T0} 954b1 "817" "" {T0} 954b2 "818" "" {T0} 954b3 "819" "" {T0} 954b4 "820" "" {T0} 954b5 "821" "" {T0} 954b6 "822" "" {T0} 954b7 "823" "" {T0} 954b8 "824" "" {T0} 954b9 "825" "" {T0} 954b10 "826" "" {T0} 954b11 "827" "" {T0} 954b12 "828" "" {T0} 954b13 "829" "" {T0} 954b14 "830" "" {T0} 954b15 "831" "" {T0} 955 "Warnings 832-847" "" {T0} 955b0 "832" "" {T0} 955b1 "833" "" {T0} 955b2 "834" "" {T0} 955b3 "835" "" {T0} 955b4 "836" "" {T0} 955b5 "837" "" {T0} 955b6 "838" "" {T0} 955b7 "839" "" {T0} 955b8 "840" "" {T0} 955b9 "841" "" {T0} 955b10 "842" "" {T0} 955b11 "843" "" {T0} 955b12 "844" "" {T0} 955b13 "845" "" {T0} 955b14 "846" "" {T0} 955b15 "847" "" {T0} 956 "Warnings 848-863" "" {T0} 956b0 "848" "" {T0} 956b1 "849" "" {T0} 956b2 "850" "" {T0} 956b3 "851" "" {T0} 956b4 "852" "" {T0} 956b5 "853" "" {T0} 956b6 "854" "" {T0} 956b7 "855" "" {T0} 956b8 "856" "" {T0} 956b9 "857" "" {T0} 956b10 "858" "" {T0} 956b11 "859" "" {T0} 956b12 "860" "" {T0} 956b13 "861" "" {T0} 956b14 "862" "" {T0} 956b15 "863" "" {T0} 957 "Warnings 864-879" "" {T0} 957b0 "864" "" {T0} 957b1 "865" "" {T0} 957b2 "866" "" {T0} 957b3 "867" "" {T0} 957b4 "868" "" {T0} 957b5 "869" "" {T0} 957b6 "870" "" {T0} 957b7 "871" "" {T0} 957b8 "872" "" {T0} 957b9 "873" "" {T0} 957b10 "874" "" {T0} 957b11 "875" "" {T0} 957b12 "876" "" {T0} 957b13 "877" "" {T0} 957b14 "878" "" {T0} 957b15 "879" "" {T0} 958 "Warnings 880-895" "" {T0} 958b0 "880" "" {T0} 958b1 "881" "" {T0} 958b2 "882" "" {T0} 958b3 "883" "" {T0} 958b4 "884" "" {T0} 958b5 "885" "" {T0} 958b6 "886" "" {T0} 958b7 "887" "" {T0} 958b8 "888" "" {T0} 958b9 "889" "" {T0} 958b10 "890" "" {T0} 958b11 "891" "" {T0} 958b12 "892" "" {T0} 958b13 "893" "" {T0} 958b14 "894" "" {T0} 958b15 "895" "" {T0} 959 "Warnings 896-911" "" {T0} 959b0 "896" "" {T0} 959b1 "897" "" {T0} 959b2 "898" "" {T0} 959b3 "899" "" {T0} 959b4 "900" "" {T0} 959b5 "901" "" {T0} 959b6 "902" "" {T0} 959b7 "903" "" {T0} 959b8 "904" "" {T0} 959b9 "905" "" {T0} 959b10 "906" "" {T0} 959b11 "907" "" {T0} 959b12 "908" "" {T0} 959b13 "909" "" {T0} 959b14 "910" "" {T0} 959b15 "911" "" {T0} 960 "Warnings 912-927" "" {T0} 960b0 "912" "" {T0} 960b1 "913" "" {T0} 960b2 "914" "" {T0} 960b3 "915" "" {T0} 960b4 "916" "" {T0} 960b5 "917" "" {T0} 960b6 "918" "" {T0} 960b7 "919" "" {T0} 960b8 "920" "" {T0} 960b9 "921" "" {T0} 960b10 "922" "" {T0} 960b11 "923" "" {T0} 960b12 "924" "" {T0} 960b13 "925" "" {T0} 960b14 "926" "" {T0} 960b15 "927" "" {T0} 963 "Baud rate PROFIBUS" "" {T0} 964 "Equipment identification" "" {T0} 965 "Profile number, PROFIdrive" "" {T0} 967 "PROFIBUS control word" "" {T0} 967b0 "ON / OFF1" "" {T0} 967b1 "Operating condition / OFF2" "" {T0} 967b2 "Operating condition / OFF3" "" {T0} 967b3 "Enable inverter/pulse inhibit" "" {T0} 967b4 "Ramp-fct.generator enable or OC/reject traversing task" "" {T0} 967b5 "Ramp-function generator start/stop or OC/intermed. stop" "" {T0} 967b6 "Enable setpoint and activate traversing task (edge)" "" {T0} 967b7 "Reset fault memory" "" {T0} 967b8 "Jog 1 ON / OFF" "" {T0} 967b9 "Jog 2 ON / OFF" "" {T0} 967b10 "Control requested / no control requested" "" {T0} 967b11 "Start referencing / exit referencing" "" {T0} 967b12 "Open the holding brake to test" "" {T0} 967b13 "Ramp-up time zero w. control.enable or ext. block change" "" {T0} 967b14 "Open-loop torque controlled operation" "" {T0} 967b15 "Spindle positioning on or request passive referencing" "" {T0} 968 "PROFIBUS status word" "" {T0} 968b0 "Ready to power-up / not ready to power-up" "" {T0} 968b1 "Ready to run or no fault" "" {T0} 968b2 "Status, controller enable" "" {T0} 968b3 "Fault available / no fault present" "" {T0} 968b4 "No OFF2 / OFF2 effective" "" {T0} 968b5 "No OFF3 / OFF3 effective" "" {T0} 968b6 "Power-on / No power-on inhibit" "" {T0} 968b7 "Alarm effective / No alarm present" "" {T0} 968b8 "n_set = n_act or no following error" "" {T0} 968b9 "Control requested" "" {T0} 968b10 "Comparison value reached or reference position reached" "" {T0} 968b11 "Reference point set / no reference point set" "" {T0} 968b12 "Setpoint acknowledge" "" {T0} 968b13 "Fct. generator active or drive is stationary / drive moving" "" {T0} 968b14 "Open-loop torque controlled operation" "" {T0} 968b15 "Spindle positioning on or request passive referencing" "" {T0} 969 "Current time difference" "" {T0} 972 "Request POWER-ON RESET" "" {T0} 979 "Encoder format" "" {T0} 979b0 " " "" {T0} 979b1 " " "" {T0} 979b2 " " "" {T0} 979b3 " " "" {T0} 979b4 " " "" {T0} 979b5 " " "" {T0} 979b6 " " "" {T0} 979b7 " " "" {T0} 979b8 " " "" {T0} 979b9 " " "" {T0} 979b10 " " "" {T0} 979b11 " " "" {T0} 979b12 " " "" {T0} 979b13 " " "" {T0} 979b14 " " "" {T0} 979b15 " " "" {T0} 979b16 " " "" {T0} 979b17 " " "" {T0} 979b18 " " "" {T0} 979b19 " " "" {T0} 979b20 " " "" {T0} 979b21 " " "" {T0} 979b22 " " "" {T0} 979b23 " " "" {T0} 979b24 " " "" {T0} 979b25 " " "" {T0} 979b26 " " "" {T0} 979b27 " " "" {T0} 979b28 " " "" {T0} 979b29 " " "" {T0} 979b30 " " "" {T0} 979b31 " " "" {T0} 980 "Number list_1" "" {T0} 981 "Number list_2" "" {T0} 982 "Number list_3" "" {T0} 983 "Number list_4" "" {T0} 984 "Number list_5" "" {T0} 985 "Number list_6" "" {T0} 986 "Number list_7" "" {T0} 987 "Number list_8" "" {T0} 988 "Number list_9" "" {T0} 989 "Number list_10" "" {T0} 1000 "Current controller cycle" "" {T0} 1001 "Speed controller cycle" "" {T0} 1003 "STS configuration" "" {T0} 1003b4 "Supersine" "" {T0} 1003b5 "Masking pulse suppression" "" {T0} 1003b6 "Time base TBSYN" "" {T0} 1003b7 "Time base ATD" "" {T0} 1003b8 "SYNO synchronization" "" {T0} 1003b9 "Time base EX_TBYN" "" {T0} 1003b10 "STROBE -> XINT division ratio" "" {T0} 1004 "Structure configuration" "" {T0} 1004b4 "Integrator control" "" {T0} 1004b8 "Fine interpolation in positioning mode" "" {T0} 1004b9 "Dead time calibr., pos. ref. value coupling via Profibus DP" "" {T0} 1005 "IM encoder pulse number" "" {T0} 1006 "IM encoder code number" "" {T0} 1007 "DM encoder pulse number" "" {T0} 1008 "IM encoder phase error correction" "" {T0} 1009 "Position controller cycle" "" {T0} 1010 "Interpolation cycle" "" {T0} 1011 "IM configuration, actual value sensing" "" {T0} 1011b0 "Inversion, speed actual value" "" {T0} 1011b1 "Encoder phase error compensation" "" {T0} 1011b2 "Resolver resolution" "" {T0} 1011b12 "Identify coarse position" "" {T0} 1011b13 "Identify fine position" "" {T0} 1011b14 "EnDat transmission rate, bit 0 (LSB)" "" {T0} 1011b15 "EnDat transmission rate, bit 1" "" {T0} 1012 "Function switch" "" {T0} 1012b0 "Ramp-function generator follow-up" "" {T0} 1012b2 "Ready (terminal-dependent) / no fault" "" {T0} 1012b4 "Reserved" "" {T0} 1012b5 "Suppress fault 753" "" {T0} 1012b7 "Induction motor speed actual value after pulse inhibit" "" {T0} 1012b8 "Average value filter, speed setpoint" "" {T0} 1012b12 "Power-on inhibit for alarm and OFF2/OFF3" "" {T0} 1012b13 "Power-on inhibit according to the PROFIdrive profile" "" {T0} 1012b14 "No power-on inhib. if all enab. signals are simult. entered" "" {T0} 1013 "Enable motor changeover" "" {T0} 1014 "Activate V/f operation" "" {T0} 1015 "Activate PE-MSD" "" {T0} 1016 "Commutation angle offset" "" {T0} 1017 "Start-up support" "" {T0} 1018 "IM pole pair number, resolver" "" {T0} 1019 "Current, rotor position ID" "" {T0} 1020 "Maximum rotation, rotor position identification" "Maximum movement, rotor position identification" {T0} 1021 "IM multi-turn resolution, absolute value encoder" "" {T0} 1022 "IM single-turn resolution, absolute value encoder" "" {T0} 1023 "IM diagnostics" "" {T0} 1023b0 "Lighting failure" "" {T0} 1023b1 "Signal amplitude too low" "" {T0} 1023b2 "Faulty code connection" "" {T0} 1023b3 "Overvoltage" "" {T0} 1023b4 "Undervoltage" "" {T0} 1023b5 "Overcurrent" "" {T0} 1023b6 "Fresh battery required" "" {T0} 1023b7 "Check error" "" {T0} 1023b8 "EnDat encoder cannot be used" "" {T0} 1023b9 "CD track defective on ERN1387" "" {T0} 1023b10 "Log cannot be aborted" "" {T0} 1023b11 "" ; "SSI signal level incorrect" "" {T0} 1023b12 "TIMEOUT on reading measured value" "" {T0} 1023b13 "CRC error or parity error" "" {T0} 1023b14 "" ; "SSI encoder signals an alarm" "" {T0} 1023b15 "Encoder defective" "" {T0} 1024 "IM Grid spacing" "" {T0} 1025 "IM serial number, low part" "" {T0} 1026 "IM serial number, high part" "" {T0} 1027 "IM configuration, encoder" "" {T0} 1027b2 "TTL encoder" "" {T0} 1027b3 "Absolute encoder (EnDat interface)" "" {T0} 1027b4 "Linear measuring system" "" {T0} 1027b5 "Operation without motor measuring system" "" {T0} 1027b6 "Rough synchronizing track, el. revolution" "" {T0} 1027b7 "Distance-coded measuring system" "" {T0} 1027b8 "Zero mark selection, fine sync using position controller" "" {T0} 1027b9 "Reserved for Posmo. Implementation missing" "" {T0} 1027b10 "" ; "SSI encoder: Binary code/gray code" "" {T0} 1027b11 "" ; "SSI encoder: Hierarchical/right-justified format" "" {T0} 1027b12 "" ; "SSI encoder: Parity bit active" "" {T0} 1027b13 "" ; "SSI encoder: Parity bit even/odd" "" {T0} 1027b14 "" ; "SSI encoder: Alarm bit active" "" {T0} 1027b15 "" ; "SSI encoder active" "" {T0} 1028 "IM telegram length SSI" "" {T0} 1029 "Delayed measurement, rotor position identification" "" {T0} 1030 "DM actual value sensing configuration" "" {T0} 1030b2 "Resolver resolution" "" {T0} 1030b14 "EnDat transmission rate, bit 0 (LSB)" "" {T0} 1030b15 "EnDat transmission rate, bit 1" "" {T0} 1031 "DM multi-turn resolution, absolute value encoder" "" {T0} 1032 "DM single-turn resolution, absolute value encoder" "" {T0} 1033 "DM diagnostics" "" {T0} 1033b0 "Lighting failure" "" {T0} 1033b1 "Signal amplitude too low" "" {T0} 1033b2 "Faulty code connection" "" {T0} 1033b3 "Overvoltage" "" {T0} 1033b4 "Undervoltage" "" {T0} 1033b5 "Overcurrent" "" {T0} 1033b6 "Fresh battery required" "" {T0} 1033b7 "Check error" "" {T0} 1033b8 "EnDat encoder cannot be used" "" {T0} 1033b9 "CD track defective on ERN1387" "" {T0} 1033b10 "Log cannot be aborted" "" {T0} 1033b11 "" ; "SSI signal level incorrect" "" {T0} 1033b12 "TIMEOUT on reading measured value" "" {T0} 1033b13 "CRC error or parity error" "" {T0} 1033b14 "" ; "SSI encoder signals an alarm" "" {T0} 1033b15 "Encoder defective" "" {T0} 1034 "DM grid spacing" "" {T0} 1036 "DM encoder code number" "" {T0} 1037 "DM encoder configuration" "" {T0} 1037b2 "TTL encoder" "" {T0} 1037b3 "Absolute encoder (EnDat interface)" "" {T0} 1037b4 "Linear measuring system" "" {T0} 1037b5 "Operation without direct measuring system" "" {T0} 1037b7 "Distance-coded measuring system" "" {T0} 1037b9 "Reserved for Posmo. Implementation missing" "" {T0} 1037b10 "" ; "SSI encoder: Binary code/gray code" "" {T0} 1037b11 "" ; "SSI encoder: Hierarchical/right-justified format" "" {T0} 1037b12 "" ; "SSI encoder: Parity bit active" "" {T0} 1037b13 "" ; "SSI encoder: Parity bit even/odd" "" {T0} 1037b14 "" ; "SSI encoder: Alarm bit active" "" {T0} 1037b15 "" ; "SSI encoder active" "" {T0} 1038 "DM serial number, low part" "" {T0} 1039 "DM serial number, high part" "" {T0} 1040 "DM pole pair number, resolver" "" {T0} 1041 "DM telegram length SSI" "" {T0} 1042 "Encoder 1 fine resolution G1_XIST1" "" {T0} 1043 "Encoder 1 fine resolution, absolute track G1_XIST2" "" {T0} 1044 "Encoder 2 fine resolution G2_XIST1" "" {T0} 1045 "Encoder 2 fine resolution, absolute track G2_XIST2" "" {T0} 1050 "IM reference mark clearance for distance-coded scales" "" {T0} 1051 "IM ref. mark clearance for distance-coded rotary encoders" "" {T0} 1052 "DM reference mark distance for distance-coded scales" "" {T0} 1053 "DM ref. mark distance for distance-coded rotary encoders" "" {T0} 1075 "Rotor position identification technique" "" {T0} 1076 "Load moment of inertia RLI" "Load mass RLI" {T0} 1077 "Integral action time, RLI controller" "" {T0} 1078 "Max. duration, rotor position identification." "" {T0} 1080 "Calculate controller data" "" {T0} 1081 "Calculate equivalent circuit diagram data" "" {T0} 1082 "Calculate third-party motor" "" {T0} 1083 "Function selection, motor data optimization" "" {T0} 1084 "Start motor data optimization" "" {T0} 1099 "Limiting factor, power section currents" "" {T0} 1100 "Pulse width modulation frequency" "" {T0} 1101 "Calc. deadtime current control loop" "" {T0} 1102 "Motor code number" "" {T0} 1103 "Rated motor current" "" {T0} 1104 "Maximum motor current" "" {T0} 1105 "Reduction in maximum motor current" "" {T0} 1106 "Power section code number" "" {T0} 1107 "Transistor limiting current" "" {T0} 1108 "Limiting current, power section (RMS)" "" {T0} 1109 "Limiting current, power section S6 (RMS)" "" {T0} 1110 "Power section version" "" {T0} 1111 "Rated current, power section (RMS)" "" {T0} 1112 "No. of pole pairs of motor" "" {T0} 1113 "Torque constant" "Force constant" {T0} 1114 "Voltage constant" "" {T0} 1115 "Armature resistance" "" {T0} 1116 "Armature inductance" "" {T0} 1117 "Moment of inertia of motor" "Motor mass" {T0} 1118 "Motor zero-speed current" "" {T0} 1119 "Series reactor inductance" "" {T0} 1120 "Current controller P gain" "" {T0} 1121 "Current controller reset time" "" {T0} 1122 "Motor current limit" "" {T0} 1123 "Load moment of inertia" "Load weight" {T0} 1124 "Symmetrizing reference model current" "" {T0} 1125 "Ramp-up time 1 for V/f operation" "" {T0} 1126 "Ramp-up time 2 for V/f operation" "" {T0} 1127 "Voltage at f = 0 V/f operation" "" {T0} 1128 "Optimum load angle" "" {T0} 1129 "Cosine Phi power factor" "" {T0} 1130 "Rated motor power" "" {T0} 1132 "Rated motor voltage" "" {T0} 1134 "Rated motor frequency" "" {T0} 1135 "Motor no-load voltage" "" {T0} 1136 "Motor no-load current" "" {T0} 1137 "Stator resistance cold" "" {T0} 1138 "Rotor resistance cold" "" {T0} 1139 "Stator leakage reactance" "" {T0} 1140 "Rotor leakage reactance" "" {T0} 1141 "Magnetizing reactance" "" {T0} 1142 "Threshold speed field weakening" "Motor threshold speed for field weakening" {T0} 1143 "Upper speed Lh characteristic" "" {T0} 1144 "Amplification factor Lh characteristic" "" {T0} 1145 "Stall torque reduction factor" "" {T0} 1146 "Maximum motor speed" "Maximum motor velocity" {T0} 1147 "Speed limitation" "Velocity limiting, motor" {T0} 1148 "Threshold speed stall power" "" {T0} 1149 "Reluctance torque constant" "" {T0} 1150 "P-gain flux controller" "" {T0} 1151 "Reset time flux controller" "" {T0} 1160 "Threshold speed flux sensing" "" {T0} 1161 "Fixed DC link voltage" "" {T0} 1162 "Min. DC link voltage" "" {T0} 1163 "Max. DC link voltage" "" {T0} 1170 "Pole pair width" "" {T0} 1171 "Line supply voltage 480 V" "" {T0} 1173 "Highest load time, power module" "" {T0} 1174 "Pulse cancellation time, power module" "" {T0} 1175 "Synchr. reduction factor for P1108" "" {T0} 1176 "Synchr. reduction factor for P1109" "" {T0} 1177 "Synchr. reduction factor for P1111" "" {T0} 1178 "Synchr. current reduction factor" "" {T0} 1179 "Asynchr. current reduction factor" "" {T0} 1180 "Lower current limit adaption" "" {T0} 1181 "Upper current limit adaption" "" {T0} 1182 "Factor, current controller adaption" "" {T0} 1185 "Start-up factor P_IREG" "" {T0} 1200 "No. of current setpoint filters" "" {T0} 1201 "Current setpoint filter type" "" {T0} 1201b0 "1st filter: 0=lowpass / 1=bandstop" "" {T0} 1201b1 "2nd filter: 0=lowpass / 1=bandstop" "" {T0} 1201b2 "3rd filter: 0=lowpass / 1=bandstop" "" {T0} 1201b3 "4th filter: 0=lowpass / 1=bandstop" "" {T0} 1201b15 "new bandstop filters: 0=old / 1=new" "" {T0} 1202 "Natural frequency current setp. filter 1" "" {T0} 1203 "Damping, current setp. filter 1" "" {T0} 1204 "Natural frequency current setp. filter 2" "" {T0} 1205 "Damping, current setp. filter 2" "" {T0} 1206 "Natural frequency current setp. filter 3" "" {T0} 1207 "Damping, current setp. filter 3" "" {T0} 1208 "Natural frequency current setp. filter 4" "" {T0} 1209 "Damping, current setp. filter 4" "" {T0} 1210 "Blocking freq. current setp. filter 1" "" {T0} 1211 "Bandwidth, current setp. filter 1" "" {T0} 1212 "Numerator, bandwidth current setpoint filter 1" "" {T0} 1213 "Blocking freq. current setp. filter 2" "" {T0} 1214 "Bandwidth, current setp. filter 2" "" {T0} 1215 "Numerator, bandwidth current setpoint filter 2" "" {T0} 1216 "Blocking freq. current setp. filter 3" "" {T0} 1217 "Bandwidth, current setp. filter 3" "" {T0} 1218 "Numerator, bandwidth current setpoint filter 3" "" {T0} 1219 "Blocking freq. current setp. filter 4" "" {T0} 1220 "Bandwidth, current setp. filter 4" "" {T0} 1221 "Numerator, bandwidth current setpoint filter 4" "" {T0} 1222 "BSF natural frequency, current setpoint filter 1" "" {T0} 1223 "BSF natural frequency, current setpoint filter 2" "" {T0} 1224 "BSF natural frequency, current setpoint filter 3" "" {T0} 1225 "BSF natural frequency, current setpoint filter 4" "" {T0} 1230 "1st torque limit value" "1st force limit value" {T0} 1233 "Generative limitation" "" {T0} 1235 "1st power limit" "" {T0} 1237 "Maximum generative power" "" {T0} 1238 "Current limit value" "" {T0} 1240 "Torque setpoint offset (speed-contr.)" "Force setpoint offset (speed-contr.)" {T0} 1241 "Normalization of torque setpoint" "Normalization of force setpoint" {T0} 1242 "Torque setpoint offset (torque-contr.)" "Offset, force setpoint (torque-controlled)" {T0} 1243 "Normalization, torque/power reduction." "Normalization, force/power reduction." {T0} 1244 "Characteristic type, torque/power reduction" "Characteristic type, force/power reduction" {T0} 1245 "Threshold, speeddependent M_set smoothing" "Threshold, velocity-dependent F_set smoothing" {T0} 1246 "Hysteresis, speeddependent M_set smoothing" "Hysteresis, velocity-dependent F_set smoothing" {T0} 1247 "Speed threshold, motor changeover 1 / 2" "" {T0} 1248 "Speed threshold, motor changeover 3 / 4" "" {T0} 1249 "External contactor control, motor changeover" "" {T0} 1250 "Frequency limit, act. current smoothing" "" {T0} 1251 "Time constant (smoothing) motor utilization" "" {T0} 1252 "Frequency limit, torque setpoint smoothing" "Frequency limit, force setpoint smoothing" {T0} 1254 "Time constant current monitoring" "" {T0} 1256 "Ramp-function generator ramp-up time" "" {T0} 1257 "Ramp-function generator ramp-down time" "" {T0} 1259 "Torque/power reduction mot./gen." "Force/power reduction mot./gen." {T0} 1260 "i2t limiting, limit current, power section S6" "" {T0} 1261 "i2t limiting, rated current power section current" "" {T0} 1262 "i2t time in limiting" "" {T0} 1263 "i2t actual limiting factor" "" {T0} 1264 "i2t actual utilization factor" "" {T0} 1267 "Pulsed resistor: Actual utilization factor" "" {T0} 1400 "Rated motor speed" "Rated motor velocity" {T0} 1401 "Speed for max. useful motor speed" "Velocity for max. useful motor velocity" {T0} 1403 "Creep speed pulse suppression" "creep speed, pulse suppression" {T0} 1404 "Timer pulse suppression" "" {T0} 1405 "Monitoring speed, motor" "Monitoring velocity, motor" {T0} 1407 "Speed controller P gain" "Velocity controller P gain" {T0} 1408 "P gain, upper adaption speed" "P gain, upper adaption velocity" {T0} 1409 "Speed controller reset time" "Velocity controller reset time" {T0} 1410 "Integral action time, upper adaption speed" "Integral action time, upper adaption velocity" {T0} 1411 "Lower adaptation speed" "Lower adaption velocity, motor" {T0} 1412 "Upper adaptation speed" "Upper adaption speed, motor" {T0} 1413 "Select speed controller adaptation" "Select velocity control adaption" {T0} 1414 "Natural frequency, reference model speed" "Natural frequency, reference model velocity" {T0} 1415 "Damping, reference model speed" "Damping, reference model velocity" {T0} 1416 "Balancing, reference model, speed" "Balancing, reference model, velocity" {T0} 1417 "n_x for 'n_act < n_x' signal" "" {T0} 1418 "n_min for 'n_act < n_min' signal" "" {T0} 1421 "Time constant, integrator feedback (n controller)" "" {T0} 1426 "Toler.bandwidth f.'n_set = n_act' signal" "" {T0} 1427 "Delay time 'n_set = n_act' signal" "" {T0} 1428 "Threshold torque M_x" "Threshold force F_x" {T0} 1429 "Delay time 'M < M_x' signal" "Delay time 'F < F_x' signal" {T0} 1451 "P gain speed controller AM" "" {T0} 1453 "Reset time speed controller AM" "" {T0} 1458 "Current setpoint, controlled range IM" "" {T0} 1459 "Torque smoothing time constant IM" "" {T0} 1465 "Switching speed MSD/AM" "" {T0} 1466 "Changeover speed, open-loop/closed-loop control IM" "" {T0} 1500 "No. of speed setpoint filters" "No. of velocity setpoint filters" {T0} 1501 "Type of speed setpoint filter" "Type of velocity setpoint filter" {T0} 1501b0 "1st filter: 0=lowpass / 1=bandstop" "" {T0} 1501b1 "2nd filter: 0=lowpass / 1=bandstop" "" {T0} 1501b8 "1st filter: 0=PT2 / 1=PT1 with lowpass" "" {T0} 1501b9 "2nd filter: 0=PT2 / 1=PT1 with lowpass" "" {T0} 1501b15 "new bandstop filters: 0=old / 1=new" "" {T0} 1502 "Time constant, speed setpoint filter 1" "Time constant, velocity setpoint filter 1" {T0} 1503 "Time constant, speed setpoint filter 2" "Time constant, velocity setpoint filter 2" {T0} 1506 "Natural frequency, speed setpoint filter 1" "Natural frequency, velocity setpoint filter 1" {T0} 1507 "Damping, speed setpoint filter 1" "Damping, velocity setpoint filter 1" {T0} 1508 "Natural frequency, speed setpoint filter 2" "Natural frequency, velocity setpoint filter 2" {T0} 1509 "Damping, speed setpoint filter 2" "Damping, velocity setpoint filter 2" {T0} 1514 "Blocking frequency, speed setpoint filter 1" "Blocking frequency, velocity setpoint filter 1" {T0} 1515 "Bandwidth, speed setpoint filter 1" "Bandwidth, velocity setpoint filter 1" {T0} 1516 "Numerator, bandwidth speed setpoint filter 1" "Numerator, bandwidth velocity setpoint filter 1" {T0} 1517 "Blocking frequency, speed setpoint filter 2" "Blocking frequency, velocity setpoint filter 2" {T0} 1518 "Bandwidth, speed setpoint filter 2" "Bandwidth, velocity setpoint filter 2" {T0} 1519 "Numerator, bandwidth speed setpoint filter 2" "Numerator, bandwidth velocity setpoint filter 2" {T0} 1520 "BSP natural frequency, speed setpoint filter 1" "BSF natural frequency velocity setpoint filter 1" {T0} 1521 "BSP natural frequency, speed setpoint filter 2" "BSP natural frequency, velocity setpoint filter 2" {T0} 1522 "Time constant, speed actual value filter (PT1)" "Time constant, velocity actual value filter (PT1)" {T0} 1600 "Suppressible faults 1" "" {T0} 1600b4 "Meas. circ. motor meas. system" "" {T0} 1600b5 "Absolute track monitoring" "" {T0} 1600b7 "Synchronization error rotor position" "" {T0} 1600b8 "Zero mark monitoring, motor measuring system" "" {T0} 1600b9 "Converter limit frequency too high" "" {T0} 1600b12 "Measuring circuit, direct measuring system" "" {T0} 1600b13 "Monitoring, absolute track dir. measuring system" "" {T0} 1600b14 "Zero mark monitoring, direct measuring system" "" {T0} 1600b17 "Hardware defect, terminal pulse enable" "" {T0} 1601 "Suppressible faults 2" "" {T0} 1601b1 "Error in A/D conversion Trm.56/14 or Trm.24/20" "" {T0} 1601b5 "Position controller output limited" "" {T0} 1601b6 "Flux controller at stop" "" {T0} 1601b7 "Current controller at stop" "" {T0} 1601b8 "Speed controller at stop" "" {T0} 1601b9 "Encoder limit frequency exceeded" "" {T0} 1601b13 "Motor temperature: shutdown limit (P1607) exceeded" "" {T0} 1601b14 "Delayed shutdown for motor overtemp. (P1602/P1603)" "" {T0} 1601b15 "DM encoder limiting frequency exceeded" "" {T0} 1601b18 "Sum of the phase currents not equal to zero" "" {T0} 1601b19 "Measuring circuit error absolute current (hardware)" "" {T0} 1601b20 "24V electronics power supply too low" "" {T0} 1601b21 "24V electronics power supply too high" "" {T0} 1601b22 "Motor holding brake defective" "" {T0} 1601b23 "Brake sequence control inactive" "" {T0} 1602 "Alarm threshold, motor overtemperature" "" {T0} 1603 "Motor temperature alarm timer" "" {T0} 1604 "DC link undervoltage warning threshold" "" {T0} 1605 "Timer n controller at stop" "" {T0} 1606 "Threshold n controller at stop" "" {T0} 1607 "Shutdown limit motor temperature" "" {T0} 1608 "Fixed temperature" "" {T0} 1610 "Diagnostic functions" "" {T0} 1610b0 "dn/dt monitoring" "" {T0} 1610b1 "Rotational accuracy monitor" "" {T0} 1611 "Response threshold dn/dt" "" {T0} 1612 "Shutdown response, faults 1" "" {T0} 1612b1 "Measuring circuit error, absolute current" "" {T0} 1612b4 "Meas. circ. motor meas. system" "" {T0} 1612b5 "Absolute track monitoring" "" {T0} 1612b7 "Synchronization error rotor position" "" {T0} 1612b8 "Zero mark monitoring, motor measuring system" "" {T0} 1612b9 "Converter limit frequency too high" "" {T0} 1612b12 "Measuring circuit, direct measuring system" "" {T0} 1612b13 "Monitoring, absolute track dir. measuring system" "" {T0} 1612b14 "Zero mark monitoring, direct measuring system" "" {T0} 1612b15 "Heatsink temperature exceeded" "" {T0} 1612b16 "Electronics temperature exceeded" "" {T0} 1612b17 "Hardware defect, terminal pulse enable" "" {T0} 1613 "Shutdown response, faults 2" "" {T0} 1613b1 "Error in A/D conversion Trm.56/14 or Trm.24/20" "" {T0} 1613b2 "Open-loop torque controlled oper. w/o encoder is not perm." "" {T0} 1613b3 "Changeover to non-parameterized motor data set" "" {T0} 1613b5 "Position controller output limited" "" {T0} 1613b6 "Flux controller at stop" "" {T0} 1613b7 "Current controller at stop" "" {T0} 1613b8 "Speed controller at stop" "" {T0} 1613b9 "Encoder limit frequency exceeded" "" {T0} 1613b10 "Rotor position identification has failed" "" {T0} 1613b11 "Illegal motion during rotor position identification" "" {T0} 1613b12 "Illegal current during rotor position identification" "" {T0} 1613b13 "Motor temperature: shutdown limit (P1607) exceeded" "" {T0} 1613b14 "Delayed shutdown for motor overtemp. (P1602/P1603)" "" {T0} 1613b15 "DM encoder limiting frequency exceeded" "" {T0} 1613b16 "DC link undervoltage" "" {T0} 1613b17 "DC link overvoltage" "" {T0} 1613b18 "Sum of the phase currents not equal to zero" "" {T0} 1613b19 "Measuring circuit error absolute current (hardware)" "" {T0} 1613b20 "24V electronics power supply too low" "" {T0} 1613b21 "24V electronics power supply too high" "" {T0} 1615 "Tolerance rotational accuracy monitor" "" {T0} 1616 "Diagnosis, actual speed value" "" {T0} 1618 "Test functions 1" "" {T0} 1619 "Test functions 2" "" {T0} 1620 "Bits for variable signaling function" "" {T0} 1620b0 "Variable signaling function" "" {T0} 1620b1 "Segment variable signaling function" "" {T0} 1620b2 "Comparison with sign" "" {T0} 1621 "Signal number, variable signaling function" "" {T0} 1622 "Address, variable signaling function" "" {T0} 1623 "Threshold, variable signaling function" "" {T0} 1624 "Hysteresis, variable signaling function" "" {T0} 1625 "Pull-in delay, variable signaling function" "" {T0} 1626 "Drop-out delay, variable signaling function" "" {T0} 1630 "Response threshold, DC link monitoring" "" {T0} 1631 "Response threshold generator axis" "" {T0} 1632 "Voltage step for generator control" "" {T0} 1633 "Cutoff threshold for generator mode" "" {T0} 1634 "Response threshold emergency retraction" "" {T0} 1635 "Minimum speed generator axis" "Minimum velocity generator axis" {T0} 1636 "Mode, emergency retraction/regenerative operation" "" {T0} 1637 "Deceleration time, regenerative braking" "" {T0} 1638 "Emergency retraction time" "" {T0} 1639 "Emergency retraction speed" "Emergency retraction velocity, motor" {T0} 1640 "Armature short-circuit, fault 1" "" {T0} 1640b1 "Measuring circuit error, absolute current" "" {T0} 1640b4 "Meas. circ. motor meas. system" "" {T0} 1640b5 "Absolute track monitoring" "" {T0} 1640b7 "Synchronization error rotor position" "" {T0} 1640b8 "Zero mark monitoring, motor measuring system" "" {T0} 1640b9 "Converter limit frequency too high" "" {T0} 1640b12 "Measuring circuit, direct measuring system" "" {T0} 1640b13 "Absolute track monitoring" "" {T0} 1640b14 "Zero mark monitoring, direct measuring system" "" {T0} 1640b15 "Heatsink temperature exceeded" "" {T0} 1640b16 "Electronics temperature exceeded" "" {T0} 1640b17 "Hardware defect, terminal pulse enable" "" {T0} 1641 "Armature short-circuit, fault 2" "" {T0} 1641b2 "Open-loop torque controlled oper. w/o encoder is not perm." "" {T0} 1641b3 "Changeover to non-parameterized motor data set" "" {T0} 1641b5 "Position controller output limited" "" {T0} 1641b6 "Flux controller at stop" "" {T0} 1641b7 "Current controller at stop" "" {T0} 1641b8 "Speed controller at stop" "" {T0} 1641b9 "Encoder limit frequency exceeded" "" {T0} 1641b10 "Rotor position identification has failed" "" {T0} 1641b11 "Illegal motion during rotor position identification" "" {T0} 1641b12 "Illegal current during rotor position identification" "" {T0} 1641b13 "Motor temperature: shutdown limit (P1607) exceeded" "" {T0} 1641b14 "Delayed shutdown for motor overtemp. (P1602/P1603)" "" {T0} 1641b15 "DM encoder limiting frequency exceeded" "" {T0} 1641b16 "DC link undervoltage" "" {T0} 1641b17 "DC link overvoltage" "" {T0} 1641b18 "Sum of the phase currents not equal to zero" "" {T0} 1641b19 "Measuring circuit error absolute current (hardware)" "" {T0} 1641b20 "24V electronics power supply too low" "" {T0} 1641b21 "24V electronics power supply too high" "" {T0} 1642 "Shutdown response, various faults" "" {T0} 1642b0 "NMI due to Watchdog" "" {T0} 1650 "Diagnostics control" "" {T0} 1650b0 "Min/Max memory" "" {T0} 1650b1 "Min/Max memory segment" "" {T0} 1650b2 "Comparison with sign" "" {T0} 1650b15 "Cycl. display of parameter number" "" {T0} 1651 "Signal number, min/max memory" "" {T0} 1652 "Memory location min/max memory" "" {T0} 1653 "Minimum value Min/Max memory" "" {T0} 1654 "Maximum value Min/Max memory" "" {T0} 1655 "Segment memory location monitor" "" {T0} 1656 "Address memory location monitor" "" {T0} 1657 "Value display monitor" "" {T0} 1657b0 " " "" {T0} 1657b1 " " "" {T0} 1657b2 " " "" {T0} 1657b3 " " "" {T0} 1657b4 " " "" {T0} 1657b5 " " "" {T0} 1657b6 " " "" {T0} 1657b7 " " "" {T0} 1657b8 " " "" {T0} 1657b9 " " "" {T0} 1657b10 " " "" {T0} 1657b11 " " "" {T0} 1657b12 " " "" {T0} 1657b13 " " "" {T0} 1657b14 " " "" {T0} 1657b15 " " "" {T0} 1657b16 " " "" {T0} 1657b17 " " "" {T0} 1657b18 " " "" {T0} 1657b19 " " "" {T0} 1657b20 " " "" {T0} 1657b21 " " "" {T0} 1657b22 " " "" {T0} 1657b23 " " "" {T0} 1658 "Value input monitor" "" {T0} 1658b0 " " "" {T0} 1658b1 " " "" {T0} 1658b2 " " "" {T0} 1658b3 " " "" {T0} 1658b4 " " "" {T0} 1658b5 " " "" {T0} 1658b6 " " "" {T0} 1658b7 " " "" {T0} 1658b8 " " "" {T0} 1658b9 " " "" {T0} 1658b10 " " "" {T0} 1658b11 " " "" {T0} 1658b12 " " "" {T0} 1658b13 " " "" {T0} 1658b14 " " "" {T0} 1658b15 " " "" {T0} 1658b16 " " "" {T0} 1658b17 " " "" {T0} 1658b18 " " "" {T0} 1658b19 " " "" {T0} 1658b20 " " "" {T0} 1658b21 " " "" {T0} 1658b22 " " "" {T0} 1658b23 " " "" {T0} 1659 "Value acceptance monitor" "" {T0} 1701 "DC link voltage" "" {T0} 1702 "Motor temperature 840D" "" {T0} 1703 "Lead time, motor measuring system conversion" "" {T0} 1704 "Lead time, conversion direct measuring system" "" {T0} 1705 "Voltage setpoint (rms)" "" {T0} 1706 "Motor speed setpoint 840D" "Velocity setpoint, motor 840D" {T0} 1707 "Actual motor speed 840D" "Velocity actual value, motor 840D" {T0} 1708 "Torque generating current Iq" "" {T0} 1709 "Significance, voltage representation" "" {T0} 1710 "Significance, current representation" "" {T0} 1711 "Significance, speed representation" "Significance, velocity representation" {T0} 1712 "Significance, rotor flux representation" "" {T0} 1713 "Significance torque representation" "Significance, force representation" {T0} 1716 "Torque setpoint" "Force setpoint" {T0} 1717 "Limiting factor for torque/power" "Limiting factor for force/power" {T0} 1718 "Torque-generating current Iq (A)" "" {T0} 1719 "Actual absolute current (rms)" "" {T0} 1723 "Diagnosis, ramp-up time" "" {T0} 1724 "Diagnosis, rotational accuracy monitor" "" {T0} 1725 "Normalization of torque setpoint" "Normalization of force setpoint" {T0} 1726 "Calculated jerk time" "" {T0} 1727 "Status display for SimoCom U" "" {T0} 1727b0 "Possible to activate direct measuring system" "" {T0} 1727b1 "TTL encoder as direct measuring system" "" {T0} 1729 "Actual rotor position (electrical)" "" {T0} 1731 "Image ZK1_PO register" "" {T0} 1731b1 "Monitoring current space vector" "" {T0} 1731b4 "Meas. circ. motor meas. system" "" {T0} 1731b5 "Absolute track monitoring" "" {T0} 1731b7 "Synchronization error rotor position" "" {T0} 1731b8 "Zero mark monitoring, motor measuring system" "" {T0} 1731b9 "Converter limit frequency too high" "" {T0} 1731b10 "Error in center frequency measurement" "" {T0} 1731b11 "Measured value memory active" "" {T0} 1731b15 "Temperature monitoring power section" "" {T0} 1732 "Image ZK1_RES register" "" {T0} 1732b1 "Error in A/D conversion Trm.56/14 or Trm.24/20" "" {T0} 1732b2 "Open-loop torque controlled oper. w/o encoder is not perm." "" {T0} 1732b3 "Changeover to non-parameterized motor data set" "" {T0} 1732b5 "Position controller output limited" "" {T0} 1732b6 "Flux controller at stop" "" {T0} 1732b7 "Current controller at stop" "" {T0} 1732b8 "Speed controller at stop" "" {T0} 1732b9 "Encoder limit frequency exceeded" "" {T0} 1732b10 "Rotor position identification has failed" "" {T0} 1732b11 "Inadmissible movement for rotor position identification" "" {T0} 1732b12 "Inadmissible current for rotor position identification" "" {T0} 1732b13 "Shutdown limit, motor overtemperature (P1607) exceeded" "" {T0} 1732b14 "Alarm threshold, motor overtemp. (P1602/P1603) exceeded" "" {T0} 1732b16 "DC link undervoltage" "" {T0} 1732b17 "DC link overvoltage" "" {T0} 1732b18 "Sum of the phase currents not equal to zero" "" {T0} 1733 "NPFK diagnosis counter" "" {T0} 1734 "Diagnostics, rotor position identification" "" {T0} 1735 "Processor utilization" "" {T0} 1736 "Test, rotor position identification" "" {T0} 1737 "Difference, rotor position identification" "" {T0} 1738 "No. of data backup operations in the FEPROM" "" {T0} 1739 "You must save in the FEPROM" "" {T0} 1740 "Significance, abs. speed act. value representation (fine)" "Significance, abs.velocity act.value representation(fine)" {T0} 1741 "Significance, utilization representation (fine)" "" {T0} 1742 "Significance, torque setpoint representation (fine)" "Significance, force setpoint representation (fine)" {T0} 1743 "Significance, velocity representation" "" {T0} 1744 "Weighting, velocity representation, external" "" {T0} 1745 "Weighting following error representation DSC" "" {T0} 1750 "Power module temperature" "" {T0} 1751 "Electronics temperature" "" {T0} 1752 "Speed, internal fan" "" {T0} 1753 "Speed, external fan" "" {T0} 1754 "Unformatted power module data" "" {T0} 1760 "Feedback, teach-in traversing blcok index" "" {T0} 1761 "Feedback, teach-in default block index" "" {T0} 1762 "Feedback teach-in counter" "" {T0} 1781 "Setpoint source, process data PROFIBUS" "" {T0} 1782 "Target offset PROFIBUS process data" "" {T0} 1783 "PROFIBUS parameterization data received" "" {T0} 1784 "PROFIBUS configuration data received" "" {T0} 1785 "Expanded PROFIBUS diagnostics" "" {T0} 1786 "PKW data received, PROFIBUS" "" {T0} 1787 "PKW data sent, PROFIBUS" "" {T0} 1788 "Processed data received via PROFIBUS" "" {T0} 1788b0 " " "" {T0} 1788b1 " " "" {T0} 1788b2 " " "" {T0} 1788b3 " " "" {T0} 1788b4 " " "" {T0} 1788b5 " " "" {T0} 1788b6 " " "" {T0} 1788b7 " " "" {T0} 1788b8 " " "" {T0} 1788b9 " " "" {T0} 1788b10 " " "" {T0} 1788b11 " " "" {T0} 1788b12 " " "" {T0} 1788b13 " " "" {T0} 1788b14 " " "" {T0} 1788b15 " " "" {T0} 1789 "Process data sent via PROFIBUS" "" {T0} 1789b0 " " "" {T0} 1789b1 " " "" {T0} 1789b2 " " "" {T0} 1789b3 " " "" {T0} 1789b4 " " "" {T0} 1789b5 " " "" {T0} 1789b6 " " "" {T0} 1789b7 " " "" {T0} 1789b8 " " "" {T0} 1789b9 " " "" {T0} 1789b10 " " "" {T0} 1789b11 " " "" {T0} 1789b12 " " "" {T0} 1789b13 " " "" {T0} 1789b14 " " "" {T0} 1789b15 " " "" {T0} 1790 "Meas. circ. type indirect meas. system" "" {T0} 1791 "Meas. circ. type direct meas. system" "" {T0} 1792 "Active measuring system" "" {T0} 1794 "Óption module (PROFIBUS): Version initial program loader" "" {T0} 1795 "Option module (PROFIBUS): Version firmware" "" {T0} 1796 "Initializer version" "" {T0} 1798 "Firmware date" "" {T0} 1799 "Firmware version" "" {T0} 1800 "Function generator control" "" {T0} 1801 "Function generator status" "" {T0} 1802 "Measuring function control" "" {T0} 1803 "Measuring function status" "" {T0} 1804 "Function generator operating mode" "" {T0} 1805 "Function generator curve shape" "" {T0} 1806 "Start-up function amplitude" "" {T0} 1807 "Start-up function offset" "" {T0} 1808 "Function generator limitation" "" {T0} 1809 "Function generator 2nd amplitude (staircase)" "" {T0} 1810 "Function generator period" "" {T0} 1811 "Function generator, pulse width (squarewave)" "" {T0} 1812 "Start-up function, bandwidth (FFT)" "" {T0} 1813 "Start-up function, ramp-up time to P1400" "" {T0} 1814 "Measuring function meas. type" "" {T0} 1815 "Measuring function meas. period (step change)" "" {T0} 1816 "Measuring function settling time" "" {T0} 1817 "Measuring function no. of averaging ops. (FFT)" "" {T0} 1820 "Signal number test socket 1" "" {T0} 1821 "Shift factor test socket 1" "" {T0} 1822 "Offset test socket 1" "" {T0} 1823 "Segment address test socket 1" "" {T0} 1824 "Offset address test socket 1" "" {T0} 1826 "Status test socket 1" "" {T0} 1830 "Signal number test socket 2" "" {T0} 1831 "Shift factor test socket 2" "" {T0} 1832 "Offset test socket 2" "" {T0} 1833 "Segment address test socket 2" "" {T0} 1834 "Offset address test socket 2" "" {T0} 1836 "Status test socket 2" "" {T0} 1842 "HOST: Control word simulation" "" {T0} 1845 "HOST: Analog input 1" "" {T0} 1846 "HOST: Analog input 2" "" {T0} 1870 "HOST: Load torque" "" {T0} 1880 "HOST: Background cycle (position controller cycles)" "" {T0} 1890 "HOST: ZK1_PO register" "" {T0} 1891 "HOST: ZK1_RES register" "" {T0} 1899 "Actual status display of the trace control" "" {T0} 1900 "Status word for the trace control" "" {T0} 1901 "Trace cycle" "" {T0} 1902 "Trace sample number" "" {T0} 1903 "Trace mode" "" {T0} 1904 "Trace trigger level Hi" "" {T0} 1905 "Trace trigger level Lo" "" {T0} 1906 "Trace edge trigger, delta value" "" {T0} 1907 "Trace trigger delay" "" {T0} 1908 "Trace trigger signal number" "" {T0} 1909 "Trace memory segment trigger signal" "" {T0} 1910 "Trace phys. trigger signal address" "" {T0} 1911 "Modular drive position of the trace trigger signal" "" {T0} 1912 "Trace signal number" "" {T0} 1914 "Trace memory segment" "" {T0} 1915 "Trace phys. signal address" "" {T0} 1916 "Modular drive position of the trace signal" "" {T0}